BOOMKICKER
specifikke installationsvejledninger

 Tilbage til Boomkicker forside
Vi har her samlet konkrete installationsvejledninger for nogle bådtyper. De skal kun tænkes som en hjælp, idet samme bådtype kan variere fra båd til båd. Informationen kan nås ved at “klikke” på båd modellen i oversigten.

Hvis du har information om installation af BoomKicker på både som ikke er nævnt i oversigten vil vi være meget taknemmelige for at høre fra dig. Du kan kontakte os på e-mail, fax eller telefon. På forhånd tak.

BB 10
Beneteau 235
Beneteau 370
Beneteau First 305
Bristol 27
Bystedt 29
C&C 34
Cal 22
Cal 25
Cape Dory 25
Capri 14.2
Capri 22
Capri 25
Catalina 22 Custum
Catalina 25
Catalina 27 TR/STD
Catalina 30TR
Columbia 26
Day 25
Dragon / Drage
Excalibur 26
Express 27
Fun 23
Helms 24
Hobie 33
Hunter 23
Hunter 23.5
Hunter 28.5
Hunter 30
Hunter 31
Hunter 336
Impluse 21
Impulse 21
Impulse 26
Interlake
Irwin 23
Irwin 31/30
Island Packet 31
J24
J29
J30
J92
Kirby 25
Kirby 30
Laser 28
MacGregor 26
Maine Cat 22
Matcher 37
Merit 25'
O'Day 25
O'Day 28
Olsen 30
Olsen 911S, 30'
Raider 33
Ranger 26
Ross 780
S2 6.9
S2 7.9
SR 21
Starwind 27
Tarten 33

 

 :
BB 10
BoomKicker recommended K1000
Estimated installation time Unknown
Recommended mast slide Unknown
Position of top of mast fitting from bottom of boom As close to vang fitting as possible
Position of forward edge boom fitting to back of mast As close to vang fitting as possible
Length between end pins Shortet 12cm
Spring rods used Smaller Rods
Comments  

tilbage...


Beneteau 235

Beneteau 235
BoomKicker recommended K0750
Estimated installation time 50 min.
Recommended mast slide 3/8" round
Position of top of mast fitting from bottom of boom 20" to lower screw hole
Position of forward edge boom fitting to back of mast 25" - 27" to forward edge of fitting. Vang locations vary. Position fitting just forward of vang bracket
Length between end pins 34-26"
Spring rods used Larger rod (1/2" dia.)
Comments  

tilbage...


beneteau 370

Beneteau 370
BoomKicker recommended K1500
Estimated installation time 1 hr.
Recommended mast slide 7/8" flat
Position of top of mast fitting from bottom of boom 30"
Position of forward edge boom fitting to back of mast 37"
Length between end pins Full length (53")
Spring rods used Larger diameter
Comments 1 3/16" wide slide can be used for boom fitting. Consider even larger 13/16" dia. rods.

tilbage...


beneteau first 305

Beneteau First 305
BoomKicker recommended K1000
Estimated installation time 30 Min.
Recommended mast slide 5/8" Flat
Position of top of mast fitting from bottom of boom 5" from vang fitting (approx.)
Position of forward edge boom fitting to back of mast As needed
Length between end pins Full Length (45")
Spring rods used Larger Diameter
Comments  

tilbage...


bristol 27

Bristol 27
BoomKicker recommended K1000
Estimated installation time 2 hrs
Recommended mast slide None
Position of top of mast fitting from bottom of boom 18.5"
Position of forward edge boom fitting to back of mast 33"
Length between end pins 40"
Spring rods used Larger
Comments Screw mast fitting directly to mast

tilbage...

Bystedt 29

Bystedt 29
BoomKicker recommended K1000
Estimated installation time Unknown
Recommended mast slide 1/2" Round
Position of top of mast fitting from bottom of boom 28 1/2"
Position of forward edge boom fitting to back of mast 33 7/8"
Length between end pins Full Length
Spring rods used Smaller Diameter
Comments  

tilbage...

C&C 34

C&C 34
BoomKicker recommended K1500
Estimated installation time 2 Hr.
Recommended mast slide Unknown
Position of top of mast fitting from bottom of boom 18"
Position of forward edge boom fitting to back of mast 36"
Length between end pins 47" (Shorten rods 6")
Spring rods used Larger Diameter
Comments  

tilbage...

Cal 22

Cal 22
BoomKicker recommended K0750
Estimated installation time 30 min
Recommended mast slide 3/8 dia. std.
Position of top of mast fitting from bottom of boom Measured 6" above deck.
Position of forward edge boom fitting to back of mast  
Length between end pins Full length, 36"
Spring rods used Smaller, 7/16 rods.
Comments  

tilbage...

Cal 25

Cal 25
BoomKicker recommended K1000
Estimated installation time 45 Min
Recommended mast slide 1/2" Round
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Full Length
Spring rods used Larger Rod (5/8" dia.)
Comments  

tilbage...

Cape Dory 25

Cape Dory 25
BoomKicker recommended K1000
Estimated installation time 1 hr.
Recommended mast slide Std. 3/8.
Position of top of mast fitting from bottom of boom 15"
Position of forward edge boom fitting to back of mast 35 3/4"
Length between end pins 5" shortened or 40" P-P.
Spring rods used 9/16" diameter, Smaller.
Comments Mast slot slightly too narrow for 1/4" screws. Can be widened with 1/4 drill.

tilbage...

Capri 14.2

Capri 14.2
BoomKicker recommended K0312
Estimated installation time Unknown
Recommended mast slide Unknown
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Unknown
Spring rods used Unknown
Comments  

tilbage...

Capri 22

Capri 22
BoomKicker recommended K0750
Estimated installation time 1 Hr.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom Mount the mast fitting as low as possible on the back of the mast. The slide works well and is highly recommended.
Position of forward edge boom fitting to back of mast Customers have reported two approaches. Mount the Boomkicker boom fitting in front of vang fitting, or mount at vang location and move vang fitting back about 5". Customers using the aft position report better vang power.
Length between end pins First boom position, 27", second position, 32".
Spring rods used Smaller Rod (7/16" dia.)
Comments The reef points of the Capri 22 mainsail may require the boom to raise considerably. Make sure the Boomkicker is cut long enough to reach that height. The Boomkicker has a travel of at least 6" measured between end pins from the straight position to the fully compressed position.
Customers report fixing the position of the gooseneck to prevent it from sliding, recommending sail stops, one above and another below the gooseneck. Others have reported cleating the gooseneck downhaul is sufficient.

tilbage...

Capri 25
Capri 25
BoomKicker recommended K0750
Estimated installation time 1 Hr.
Recommended mast slide 3/8 Round
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins 30"
Spring rods used Small Rods
Comments Recommend custom adaptor and B1000 Boom Fitting for Capri boom with extruded tang.

tilbage...

Catalina 22 Custum

Catalina 22 Custum
BoomKicker recommended K07C22 (special K0750)
Estimated installation time 45 Min.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom 25"
Position of forward edge boom fitting to back of mast 30.5"
Length between end pins Pre-cut (40")
Spring rods used Pre-selected (7/16" dia.)
Comments This unit is precut to fit the Catalina 22 with the proper size spring rods. Cutting down should not be necessary. This unit also includes as standard, a Quickpin for fast Boomkicker removal for trailering and using the Pop Top.
Note: For best results the gooseneck should be fixed in one location for set up and regular use. If the gooseneck slides in the luff groove it is best to fix it at its'lowest point on the mast for the sail.
We recommend putting a sail stop under the gooseneck at that point and tightening the down haul against it.

tilbage...

Catalina 25

Catalina 25
BoomKicker recommended K1000
Estimated installation time 1 Hr.
Recommended mast slide 1/2" Round
Position of top of mast fitting from bottom of boom 16 1/2"
Position of forward edge boom fitting to back of mast 32"
Length between end pins 45"
Spring rods used Cut to size.
Comments Slide Boomkicker mast bracket up or remove before stepping or unstepping mast.

tilbage...

Catalina 27 TR/STD

Catalina 27 TR/STD
BoomKicker recommended K1000
Estimated installation time 1 Hr
Recommended mast slide 1/2" Flat
Position of top of mast fitting from bottom of boom 29"
Position of forward edge boom fitting to back of mast 28"
Length between end pins 39"
Spring rods used Small Rods
Comments May have to shorten screws by 1/16"

tilbage...

Catalina 30TR
Catalina 30TR
BoomKicker recommended K1000
Estimated installation time 1.25 Hr.
Recommended mast slide 3/4" Flat
Position of top of mast fitting from bottom of boom 26.5"
Position of forward edge boom fitting to back of mast 34.5"
Length between end pins 45" Full length.
Spring rods used Larger Rods
Comments  

tilbage...

Columbia 26

Columbia 26
BoomKicker recommended K1000
Estimated installation time 1.5 Hr.
Recommended mast slide Unknown (1/2")
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Unknown
Spring rods used Larger Rods
Comments  

tilbage...

Excalibur 26

Dragon / Drage
BoomKicker recommended K1000
Estimated installation time 1.5 Hr.
Recommended mast slide Unknown
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Unknown
Spring rods used Unknown
Comments  

tilbage...

Excalibur 26
BoomKicker recommended K1000
Estimated installation time 2 Hr.
Recommended mast slide Unknown
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins 43"
Spring rods used Smaller Rods
Comments  

tilbage...

Express 27

Express 27
BoomKicker recommended K1000
Estimated installation time 3 Hr.
Recommended mast slide Unknown
Position of top of mast fitting from bottom of boom 28"
Position of forward edge boom fitting to back of mast 33 1/2"
Length between end pins Full Length
Spring rods used Larger Rods
Comments  

tilbage...

Fun 23

Fun 23
BoomKicker recommended K1000
Estimated installation time Unknown
Recommended mast slide 1/2" Round
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Unknown
Spring rods used Smaller Rods
Comments Substituted M0750 mast fitting for standard M1000 to better fit mast groove.

tilbage...

Helms 24

Helms 24
BoomKicker recommended K0750
Estimated installation time 1 Hr.
Recommended mast slide 3/4" Flat
Position of top of mast fitting from bottom of boom 22"
Position of forward edge boom fitting to back of mast 28"
Length between end pins Full Length (36")
Spring rods used Larger Rods (1/2" dia.)
Comments  

tilbage...

Hobie 33

Hobie 33
BoomKicker recommended K1000
Estimated installation time 1.5 Hr.
Recommended mast slide 1/2" round
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Full Length (45")
Spring rods used Larger Rods (5/8" dia.)
Comments  

tilbage...

Hunter 23

Hunter 23
BoomKicker recommended K0750
Estimated installation time 1 Hr.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom 5" measured from deck up to top of fitting.
Questionable number.
Position of forward edge boom fitting to back of mast 25"
Length between end pins 36"
Spring rods used Smaller Rods
Comments  

tilbage...

Hunter 23.5

Hunter 23.5
BoomKicker recommended K0750
Estimated installation time 3/4 hr
Recommended mast slide Std. 3/8 round
Position of top of mast fitting from bottom of boom 21"
Position of forward edge boom fitting to back of mast 31"
Length between end pins Full, 36"
Spring rods used Larger 1/2" dia.
Comments  

tilbage...

Hunter 28.5

Hunter 28.5
BoomKicker recommended K1000
Estimated installation time 45 min
Recommended mast slide 3/8 round
Position of top of mast fitting from bottom of boom unkown
Position of forward edge boom fitting to back of mast unkown
Length between end pins Full, 45" P-P
Spring rods used Larger
Comments May have to tap mast slot for screws.

tilbage...

Hunter 30

Hunter 30
BoomKicker recommended K1500
Estimated installation time Unknown
Recommended mast slide 3/4" Flat
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Full Length (53")
Spring rods used Smaller Rods
Comments Boom slide is 1 1/4" wide. Works great.
This boat is '88 fractional.

tilbage...

Hunter 31

Hunter 31
BoomKicker recommended K1000
Estimated installation time 30 Min.
Recommended mast slide 3/4" Flat
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Unknown
Spring rods used Unknown
Comments  

tilbage...

Hunter 336

Hunter 336
BoomKicker recommended K1500
Estimated installation time Unknown
Recommended mast slide 5/8" Flat
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Unknown
Spring rods used Unknown
Comments A Boom slide, 1/8" thick, 1 3/16" wide can be used for the boom.

tilbage...

Impluse 21

Impluse 21
BoomKicker recommended K0750
Estimated installation time 30 Min.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Full Length
Spring rods used Larger Rods
Comments Installed parallel to vang, 3" above.

tilbage...

Impluse 21

Impulse 21
BoomKicker recommended K0750
Estimated installation time 1 Hr.
Recommended mast slide Std., 3/8 Rd.
Position of top of mast fitting from bottom of boom ?
Position of forward edge boom fitting to back of mast 2" in front of vang.
Length between end pins Full?
Spring rods used Smaller
Comments  

tilbage...

Impulse 26

Impulse 26
BoomKicker recommended K1000
Estimated installation time 2 Hr.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom 21 1/8"
Position of forward edge boom fitting to back of mast 31 3/4"
Length between end pins 40 1/4"
Spring rods used Larger Rods (5/8" dia.)
Comments  

tilbage...

Interlake

Interlake
BoomKicker recommended K07INLK (special K0750)
Estimated installation time 1 Hr.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom Bottomed out against pin in luff groove. (Shorten pin 1") 14" from the bottom of the boom to the top of the bracket or about 5 1/2" off the deck.
Position of forward edge boom fitting to back of mast Just in front of vang fitting, 30" from the aft side of the mast to the forward edge of the boom fitting.
Length between end pins Pre-cut (36")
Spring rods used Pre-selected (7/16" dia.)
Comments To step or unstep the mast the mast bracket must be slid up the mast. Pull Fastpin to release Boomkicker and access the bracket screws. Customers report cutting down the mast base insert in the luff groove of the mast about 1" to lower the mast fitting. Some have used Locktight on the mast bracket screws, leaving them just loose enough so the mast fitting is easily slid up the mast. If the gooseneck is spring loaded, the spring should be replace with a spacer to prevent changing the foot tension of the mainsail. A short piece of PVC pipe works.

tilbage...

Irwin 23

Irwin 23
BoomKicker recommended K0750
Estimated installation time 1/2 hr.
Recommended mast slide Std. 3/8 round
Position of top of mast fitting from bottom of boom ?
Position of forward edge boom fitting to back of mast ?
Length between end pins ?
Spring rods used Larger
Comments  

tilbage...

Irwin 31/30

Irwin 31/30
BoomKicker recommended K1000
Estimated installation time Unknown
Recommended mast slide 3/4" Flat
Position of top of mast fitting from bottom of boom 31"
Position of forward edge boom fitting to back of mast 40" Approx
Length between end pins Full Length (45")
Spring rods used Larger Rods (5/8" dia.)
Comments Cut slides in half to fit into sail opening.

tilbage...

Island Packet 31

Island Packet 31
BoomKicker recommended K1500
Estimated installation time 1 Hr
Recommended mast slide Flat 3/4" wide
Position of top of mast fitting from bottom of boom 30"
Position of forward edge boom fitting to back of mast From aft end of boom to aft end of boom fitting, 136".
Length between end pins 49" P-P.
Spring rods used Larger, Originals in BK.
Comments  

tilbage...

J24

J24
BoomKicker recommended K0750
Estimated installation time 1 hr.
Recommended mast slide Std. 3/8 dia.
Position of top of mast fitting from bottom of boom 19" to bottom of gooseneck.
Position of forward edge boom fitting to back of mast 31"
Length between end pins Full, 36" P-P
Spring rods used Smaller
Comments  

tilbage...

J29

J29
BoomKicker recommended K1500
Estimated installation time Unknown
Recommended mast slide Unknown
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Unknown
Spring rods used Unknown
Comments There is not any good installation data for the J29. Unfortunately I don't think the included 1/2" diameter slide will fit the J29 luff groove. So the mast bracket will need to be screwed directly to the mast using the longer 5/16-18 round head screws included in the small bag.

tilbage...

J30

J30
BoomKicker recommended K1500
Estimated installation time 1.5 Hr
Recommended mast slide 7/16" Round
Position of top of mast fitting from bottom of boom 30" Just above vang/TD>
Position of forward edge boom fitting to back of mast <43 1/2"/TD>
Length between end pins Full, 53"
Spring rods used Smaller or optional 5/8"
Comments Most J30s have ordered optional 5/8"diameter rods. Mast fitting stops on mast vang plate.

tilbage...

J92

J92
BoomKicker recommended K1000
Estimated installation time 30 Min.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom 18"
Position of forward edge boom fitting to back of mast 41 1/2"
Length between end pins Full Length
Spring rods used Larger Rods (5/8" dia.)
Comments  

tilbage...

Kirby 25

Kirby 25
BoomKicker recommended K1000
Estimated installation time  
Recommended mast slide Flat 5/8"
Position of top of mast fitting from bottom of boom  
Position of forward edge boom fitting to back of mast  
Length between end pins  
Spring rods used  
Comments  

tilbage...

Kirby 30

Kirby 30
BoomKicker recommended K1000
Estimated installation time 2 Hr.
Recommended mast slide 3/4" Flat
Position of top of mast fitting from bottom of boom 30"
Position of forward edge boom fitting to back of mast 32"
Length between end pins Full Length (45")
Spring rods used Larger Rods (5/8" dia.)
Comments  

tilbage...

Laser 28

Laser 28
BoomKicker recommended K1000
Estimated installation time 1 Hr.
Recommended mast slide 3/8 Round
Position of top of mast fitting from bottom of boom 25" Just above mast base casting.
Position of forward edge boom fitting to back of mast 37" Just in front of boom fitting.
Length between end pins Full Length
Spring rods used Larger Rods (5/8" dia.)
Comments Boom should angle up above horizontal

tilbage...

MacGregor 26

MacGregor 26
BoomKicker recommended K07MX (special K0750)
Estimated installation time 30 Min.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom Measure from base of mast, 6 1/4" up to bottom of Boomkicker mast bracket.
Position of forward edge boom fitting to back of mast Measure from front of boom, not including gooseneck, back 23 1/2" to front of Boomkicker boom fitting.
Fitting should be about 5" in front of boom hole for vang bail.
Length between end pins Pre-cut (32")
Spring rods used Pre-selected (3/8" dia.)
Comments The K07MX is made specially for the MacGregor 26X. The rods are pre-selected and cut to length for easier installation. Vang bails are available from Blue Water Yachts at 206/282-4261 press 2 for parts.

tilbage...

Maine Cat 22

Maine Cat 22
BoomKicker recommended K0750
Estimated installation time .5 hrs.
Recommended mast slide Std. 3/8 rd.
Position of top of mast fitting from bottom of boom Just above base, 21.5"
Position of forward edge boom fitting to back of mast 26.5"
Length between end pins Full length, 36".
Spring rods used Larger
Comments  

tilbage...

Merit 25

Merit 25
BoomKicker recommended K0750
Estimated installation time 45 Min.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom 18 3/4" to top of mast bracket.
Position of forward edge boom fitting to back of mast 25 1/8" to forward edge of boom fitting. Vang fitting is 2 1/16" behind BK boom fitting.
Length between end pins 32"
Spring rods used Smaller Rods
Comments  

tilbage...

O'Day 25

O'Day 25
BoomKicker recommended K1000
Estimated installation time Unknown
Recommended mast slide 3/4" Flat
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Unknown
Spring rods used Unknown
Comments  

tilbage...

O'Day 28

O'Day 28
BoomKicker recommended K1000
Estimated installation time Unknown
Recommended mast slide 3/4" Flat
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins Unknown
Spring rods used Unknown
Comments  

tilbage...

Olsen 30

Olsen 30
BoomKicker recommended K1000
Estimated installation time 1 Hr.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins With 50" vang, try full length.
Spring rods used Smaller Rods (9/16" dia.)
Comments  

tilbage...

Olsen 911S, 30'

Olsen 911S, 30'
BoomKicker recommended K1500
Estimated installation time 1.5 hours
Recommended mast slide 1/2" diameter
Position of top of mast fitting from bottom of boom 6" off deck
Position of forward edge boom fitting to back of mast 36" back from mast.
Length between end pins 50"
Spring rods used Smaller, 11/16" diameter.
Comments  

tilbage...

Raider 33

Raider 33
BoomKicker recommended K1000
Estimated installation time 2 Hr.
Recommended mast slide 1/2"
Position of top of mast fitting from bottom of boom 20"
Position of forward edge boom fitting to back of mast 38"
Length between end pins 44"
Spring rods used Larger Rods
Comments  

tilbage...

Ranger 26

Ranger 26
BoomKicker recommended K1000
Estimated installation time 1 hr.
Recommended mast slide 1/2" Round
Position of top of mast fitting from bottom of boom ?
Position of forward edge boom fitting to back of mast ?
Length between end pins Full length, 45"
Spring rods used Smaller
Comments  

tilbage...

Ross 780

Ross 780
BoomKicker recommended K1000
Estimated installation time 45 Min.
Recommended mast slide Attach direct
Position of top of mast fitting from bottom of boom 29"
Position of forward edge boom fitting to back of mast 41"
Length between end pins Full Length
Spring rods used Larger Rods (5/8" dia.)
Comments  

tilbage...

S2 6.9

S2 6.9
BoomKicker recommended K0750
Estimated installation time 1 Hr.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom Unknown
Position of forward edge boom fitting to back of mast Unknown
Length between end pins 34 1/2" (Shorten rods 1 1/2")
Spring rods used Larger Rods (1/2" dia.)
Comments  

tilbage...

S2 7.9

S2 7.9
BoomKicker recommended K1000
Estimated installation time 1 Hr.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom The mast fitting amounts just above the mast base. The luff groove slide is recommended and can be inserted at the sail opening and dropped down.
Position of forward edge boom fitting to back of mast Measured from the back of the mast to the aft screw hole in the boom fitting is approximately 36". Double check Boomkicker clearance with vang before drilling, vang locations could vary.
Length between end pins Usually installed at full length.
Spring rods used Usually the smaller 9/16" dia.
Comments If using a 2 to 1 purchase plate to double the block and tackle vang, a long D shackle between the plate shackle and deck plate helps provide clearance for the block.

tilbage...

SR 21

SR 21
BoomKicker recommended K0750
Estimated installation time Unknown
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom Approx. 16"
Position of forward edge boom fitting to back of mast Unknown
Length between end pins 30" (Shorten rods 6")
Spring rods used Smaller Rods
Comments It may be necessary to relocate outhaul

tilbage...

Starwind 27

Starwind 27
BoomKicker recommended K1000
Estimated installation time Unknown
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom About 4" up from mast base.
Position of forward edge boom fitting to back of mast About 2" in front of vang boom fitting.
Length between end pins Full Length
Spring rods used Smaller Rods
Comments One customer reported removing original swivel vang from mast and mounting eye strap to accept vang. Then drilled a hole in the tang holding the Boomkicker for the second attachment of a cascading vang.

tilbage...

Tarten 33

Tarten 33
BoomKicker recommended K1500
Estimated installation time 45 Min.
Recommended mast slide 1/2" Round
Position of top of mast fitting from bottom of boom Parallel to vang tackle.
Position of forward edge boom fitting to back of mast As close to vang fitting as possible.
Length between end pins Full Length (53".)
Spring rods used Larger Rods
Comments  

tilbage...

Matcher 373

Matcher 37
BoomKicker recommended K1500
Estimated installation time 45 Min.
Recommended mast slide 3/8" Round
Position of top of mast fitting from bottom of boom As close to vang fitting as possible.
Position of forward edge boom fitting to back of mast Unknown.
Length between end pins Full Length (53".)
Spring rods used Larger Rods
Comments  

tilbage...